Anatomy of a Deck

A durable deck is much more than boards. Discover each component, from the footings to the railing, and what it does. Hover over or tap a part of the drawing to see what it is, then zoom in to see the details.

Hover over or tap a part to see what it is. Use + and − to zoom.

  1. Footings (piles)

    Anchor the deck in the ground, below the frost line.

    Screw piles or concrete piers poured into cardboard tube forms (Sonotubes) carry the entire weight of the deck down to the ground. In Quebec, they must go below the frost line, often 1.2 m (4 ft) or more depending on the region, so frost can't lift the structure. Check your municipality's requirements.

  2. Posts

    Connect the footings to the beam.

    Usually 6x6 pressure-treated lumber, the posts sit on the footings and support the beam. They're fastened at both ends with galvanized metal connectors.

  3. Beam

    Supports the joists and carries the load to the posts.

    Often made of two or three 2x10s fastened together, the beam sits on the posts and supports the joists. Its size depends on the joist span and the distance between the posts.

  4. Ledger Board and Flashing

    Board fastened to the house that carries the ends of the joists.

    The ledger board is bolted to the house framing with lag screws or structural screws. The metal flashing installed above it keeps water from getting behind the ledger and rotting the wall.

  5. Joists

    The framing that supports the deck boards.

    Joists, often 2x8 or 2x10 pressure-treated lumber, run from the ledger board to the rim joist and rest on the beam. Straight, level joists give you a flat deck with no dips.

  6. Joist Spacing

    16 in (406 mm) on center for most boards.

    For most composite boards installed perpendicular to the joists, the maximum joist spacing is 16 in (406 mm) on center. It must be reduced to 12 in (305 mm) for diagonal installations, for stairs, and for some products. Always check the installation guide of the brand you choose.

  7. Joist Hangers and Connectors

    Metal hardware that holds the structure together.

    Joist hangers attach each joist to the ledger board, and other connectors tie the posts to the footings and the beam. Choose galvanized hardware rated for pressure-treated lumber, installed with the nails or screws recommended by the manufacturer.

  8. Rim Joist

    Closes off the frame at the ends of the joists.

    The rim joist ties the ends of the joists together and forms the outline of the structure. It supports the fascia, the railing posts, and the top of the stairs.

  9. Blocking

    Pieces between the joists that stiffen the structure.

    Installed between the joists, blocking keeps them from twisting and makes the deck stiffer. Extra blocking is also added to support the picture frame border, board joints, and railing posts.

  10. Joist Tape

    Protects the top of the joists from water and rot.

    This self-adhesive butyl tape goes on top of the joists, the beam, and the ledger board. It keeps water from sitting on the wood and seals around every screw. A small expense that extends the life of the structure under composite boards built to last for decades.

  11. Deck Boards

    A durable surface with no staining or sanding.

    Composite boards resist rot, stains, and fading, and they don't split. They're installed perpendicular to the joists and fastened with hidden fasteners, for a finish with no visible screws. Soap and water is all it takes to keep them clean.

  12. Hidden Fasteners

    Concealed clips that hold grooved boards in place (detail A).

    These clips slide into the groove on the side of the boards and screw into the joist. No screws show on the surface, and the gap between boards is automatically even. Use the fasteners recommended by the board manufacturer to keep the warranty valid.

  13. Gap Between Boards

    Lets water drain and the composite expand.

    A gap of about 3/16 in (5 mm) between boards lets water drain and air circulate. Hidden fasteners set it automatically. At the ends of the boards and against the house, the gap depends on the brand and on the temperature during installation: follow the manufacturer's guide.

  14. Picture Frame Border

    Finishing boards around the edge of the deck.

    One or two rows of boards installed around the edge hide the board ends and give a high-end finish, often in a contrasting color. The picture frame needs extra blocking underneath and is fastened with color-matched screws.

  15. Color-Matched Screws

    For the picture frame, the stairs, and the fascia.

    Where hidden fasteners can't be used (picture frame, stairs, fascia), boards are fastened with colored-head screws designed for composite. They blend into the board and keep the material from lifting around the screw head.

  16. Fascia

    Thin board that covers the rim joist.

    Fascia covers the rim joist and the visible framing for a clean edge that matches the deck boards. It's also used to cover the stair risers. It's fastened with color-matched screws, leaving the expansion gap specified by the manufacturer.

  17. Stair Stringers

    Notched supports that carry the stair treads.

    Stringers are cut from pressure-treated lumber and attached to the rim joist. With composite treads, they generally need to be spaced no more than 12 in (305 mm) on center.

  18. Treads and Risers

    Composite board treads, fascia-covered risers.

    Each tread is usually made of two composite boards fastened with color-matched screws, and the risers are covered with fascia. The tread nosing overhangs the riser slightly for surer footing.

  19. Aluminum Railing

    Maintenance-free posts, handrails, and balusters.

    Powder-coated aluminum railings don't rust and need no maintenance. A guardrail is required when the deck is more than 600 mm (24 in) above the ground, and the openings between balusters must not let a 100 mm (4 in) sphere pass through. The required height, usually 36 or 42 in, depends on the height of the deck and local regulations.

  20. Glass Railing

    Tempered glass panels that keep the view open.

    Tempered glass panels, held by aluminum posts and channels, protect without blocking the view. Ideal for a deck facing a pool, a lake, or a beautiful yard.

  21. Privacy Screen

    Panels that block the wind and prying eyes.

    Composite or aluminum slats fastened between posts create a private, sheltered corner that matches the deck. The posts must be anchored to the structure (joists and blocking), not just to the deck boards.

  22. LED Lighting

    Small lights for the stairs and the edges of the deck.

    LED lights recessed into the risers, fascia, or posts make the deck safer at night and highlight its shape. They run on low voltage with an outdoor transformer.